Eagle Tree Systems Seagull Glide Manual de instrucciones descargar pdf

Table of Contents

Introduction 1

Packing List 1

Specifications 1

Main Features 1

General Safety Precautions 2

Have questions or Feedback? 2

Overview/Quick Start 2

Guardian Physical Connections

and Controls 3

The Receiver Connection

Harness 4

Receiver Requirements 4

Mounting the Guardian in your

Model 6

Preflight Checks 6

First Flight 6

Tuning Stabilization Gains 7

Status LED 8

Mode/Config Switch Behavior 9

The Guardian PC Software 12

Guardian Configuration Page

Software Reference 12

Troubleshooting / F.A.Q. 14

Limited Warranty 14

Guardian 2D/3D Stabilizer

Document Version 1.5

Introduction

Thank you for your purchase! Based on Eagle Tree's proven inertial stabilization technology, the Guardian 2D/3D Stabilizer (the

Guardian) stabilizes gas or electric models, wings, foamies, sailplanes, turbines, or just about any other fixed wing model.

To stabilize your model, just mount the Guardian in a level orientation (it can even be mounted

upside down), connect it to your servos and receiver with the included cable, tune it to your

plane with a small screwdriver, and set optional features with your radio sticks. No computer

or additional equipment is required for stabilization. If desired, our powerful PC software

can also be used to quickly configure the Guardian’s advanced features (“micro” USB cable

required, but not included).

This instruction manual will guide you through the installation and operation of your

Guardian. The latest version of this manual is available in the Product Manuals section of the

Support tab on http://www.eagletreesystems.com. The online manual is in full color, and

includes any updates that were made after this manual was produced. Please read the entire

manual carefully before proceeding. If, after you read the manual, you have further

questions or problems, see the “Have Questions or Feedback?” section below.

Packing List

Your package should include the following: The Guardian, the receiver connection harness

with labeled connectors, the quick reference card, and a printed version of this manual.

Specifications

• Input Voltage Range: 4.5v to 16v

• Current Draw: Approximately 31mA

• Dimensions: 41mm x 22mm x 11mm (1.62 inches x 0.86 inches x 0.42 inches)

• Mass: 11 grams (0.4 ounces) including harness

• Maximum Servo Current through Guardian: 5 Amps

Main Features

The Guardian 2D/3D Stabilizer has two main modes of operation: 2D Mode and 3D Mode. While in flight, a spare switch on your radio

lets you switch between 2D (wing leveling) mode, 3D aerobatic mode, and no stabilization. Imagine performing a difficult 3D maneuver

with ease, then just flipping a switch to instantly return to level flight! Note: Please see the Tuning Stabilization Gains section for note on

preventing damage from re-leveling too quickly.

2D Mode

When set for 2D Mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot

easier to adjust and fly your plane. In this mode, the Guardian "remembers" level flight for your model and returns it to level flight when

needed. In 2D mode, flying in moderate wind can seem just as easy as flying in no wind at all!

Additionally, the Guardian provides precise "fly by wire" control, in which it interprets your control stick deflections as command angles

for Pitch and Roll. For example, pushing and holding your control stick left will cause your model to enter a level altitude banked left

turn. This mode is ideal for beginners as well as experts looking for a reduced workload on take-off and landing. It also can be useful for

aerobatic pilots seeking to recover quickly after losing orientation.

The Guardian also includes an advanced “Oscillation Suppression” feature that can quickly detect and eliminate oscillations stemming

from too high gains.

1 2 3 4 5 6 ... 13 14

Indice de contenidos

Pagina 1 - Main Features

Pagina 2 - Overview/Quick Start

Pagina 3

Pagina 4 - Receiver Requirements

Pagina 5 - Wing Type Configuration

Pagina 6 - First Flight

Pagina 7 - Tuning Stabilization Gains

Pagina 8 - Status LED

Pagina 9 - Mode/Config Switch Behavior

Pagina 10 - Menu Example

Pagina 11

Pagina 12 - Reference

Pagina 13 - The Advanced Tab

Pagina 14 - Troubleshooting / F.A.Q

Mas documentos para Los conmutadores de red Eagle Tree Systems Seagull Glide

a Ver el documento Eagle Tree Systems Seagull Glide Manual de usuario

Eagle Tree Systems Seagull Glide Manual de usuario (13 paginas)

a Ver el documento Eagle Tree Systems Seagull Glide Manual de instrucciones

Eagle Tree Systems Seagull Glide Manual de instrucciones (3 paginas)

Eagle Tree Systems Seagull Glide Manual de usuario (30 paginas)

Comentarios a estos manuales

Sin comentarios

Eagle Tree Systems Seagull Glide Manual de instrucciones

Busca en linea o descarga Manual de instrucciones para Los conmutadores de red Eagle Tree Systems Seagull Glide. Eagle Tree Systems Seagull Glide Instruction manual [en] [es] [fr] Manual de usuario

Indice de contenidos

Mas documentos para Los conmutadores de red Eagle Tree Systems Seagull Glide

Comentarios a estos manuales

Relacionado con productos y manuales para Los conmutadores de red Eagle Tree Systems Seagull Glide